Menvier TS690/700/790 panel with LED keypad User Instructions

Back to Index
 
Full set the system
1. Enter [User code]
2. Either wait for 3 seconds or Press [0] Exit tone sounds
Part set the system
1. Enter [User code]
2. Optionally press [8] for silent setting
3. Press [A] [B] or [C] Exit tone sounds
Unset the system
1. Enter [User code] Entry tone stops
Reset system after alarm condition
1. Enter [User code]
Remote reset after alarm condition
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [3] Display shows four digit number
4. Quote above four digit number to alarm company Ask for a "remote or coded reset"
5. Enter [reply code from alarm co]
6. Press [ENT] Confirmation tone sounds
7. Press [ESC] Display shows OPEN, then time
Omit a zone
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [7] Display shows 01-n, indicating that zone 1 is not omitted
4. Press [ENT] to move to next zone, optionally pressing [0] to toggle zone as omitted If required zone is not displayed then that zone has been programmed as not omitable
5. Press [ESC] Display shows 1-
6. Press [0] for full set, [A] [B] or [C] for part set
Change your own user code
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [4] Display shows ----
4. Enter new [User code] Display shows new code
5. Press [ENT] Display shows 1-
6. Press [ESC] Display shows OPEN, then time
Test the alarm sounders
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [1] Display shows ON 9 and sounders sound
4. Press [ESC] to end test
5. Press [ESC] Display shows OPEN, then time
Walk test the detection devices
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [2] Display shows active zones
4. Walk test detectors Sounder tone changes to indicate zone active
5. Press [ESC] Display shows 1-
6. Press [ESC] Display shows OPEN, then time
Setup user codes
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [ENT] Display shows 2-
4. Press [4] Display shows Ur --
5. Press [number of user to change] Master code is user number 1, user code 2-7 are standard user codes, code 8 can only set the system (cleaner code)
6. Press [ENT]
7. Enter new [User code] Display shows new code
8. Press [ENT] Display shows Ur --
9. Press [ESC] Display shows 2-
10. Press [ESC] Display shows 1-
11. Press [ESC] Display shows OPEN, then time
View the event log
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [ENT] Display shows 2-
4. Press [9] Display shows last event
5. Press [A] for earlier events, [C] for later events, [B] to display time of event, then [B] again for date of event
6. Press [ESC] Display shows 2-
7. Press [ESC] Display shows 1-
8. Press [ESC] Display shows OPEN, then time
Set control panel time/clock
1. Enter [User code]
2. Press [ENT] Display shows 1-
3. Press [ENT] Display shows 2-
4. Press [2] Display shows ----
5. Enter [time in 24 hour format] Display shows new time
6. Press [ENT] Display shows 2-
7. Press [3] Display shows ----
8. Enter [ddmm] Display shows new date (no years)
9. Press [ENT] Display shows 2-
10. Press [ESC] Display shows 1-
11. Press [ESC] Display shows OPEN, then time
 
  Back to Index