| Back to Index | ||
| Full set the system | ||
| 1. | Enter [user code] | |
|---|---|---|
| 2. | Press [yes/part] | Exit tone sounds. |
| Part set the system | ||
| 1. | Enter [user code] | |
| 2. | Press [yes/part] | |
| 3. | Press [yes/part] | Exit tone sounds. |
| Unset the system | ||
| 1. | Enter [user code] | Display shows [_ _]. |
| Reset system after alarm condition | ||
| 1. | Enter [user code] | Display shows[ ?]. |
| 2. | Press [yes/part] | Before the system has time to set. |
| 3. | Enter [user code] | Display shows [_ _], system now reset. |
| Remote reset after alarm condition | ||
| 1. | If display shows [AL] | |
| 2. | Enter [user code] | Display shows [ ?]. |
| 3. | Press [yes/part] | Display shows [En], then a four diget number. |
| 4. | Quote above four digit number to alarm company | Ask for a "remote or coded reset." |
| 5. | Phone your alarm company and ask for a coded reset, and give them your noted down number. | |
| 6. | Enter [reply code from alarm co] | |
| Omit a zone | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [yes/part] | Display shows [O-], select the zone to be omitted by pressing the corresponding key. |
| 4. | Press [yes/part] | To confirm selection. |
| 5. | Press [yes/part] | Again to confirm selection, display shows[O-], ready to accept the next zone to be omitted. |
| 6. | Press [0/esc] | The zones selected will be omitted next time the system is set. Display shows [_ _]. |
| Change your own user code | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [no] | Display shows [tE]. |
| 4. | Press [no] | Display shows [bE]. |
| 5. | Press [no] | Display shows [Lo]. |
| 6. | Press [no] | Display shows [Ch]. |
| 7. | Press [no] | Display shows [Co]. |
| 8. | Press [yes/part] | Display shows [U-]. |
| 9. | Press [1] | Display shows [--]. |
| 10. | Enter new [User code] | |
| 11. | Press [yes/part] | to confirm the selection. Display shows [rE]. |
| 12. | Enter new [User code] | Again to confirm the selection. |
| 13. | Press [yes/part] | If re-entered correctly a short tone is generated. Display shows [U-]. |
| 14. | Press [0/esc] | Display shows [Co]. |
| 15. | Press [0/esc] | Display shows [_ _]. |
| Test the alarm sounders | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [no] | Display shows [tE]. |
| 4. | Press [no] | Display shows [bE]. |
| 5. | Press [yes/part] | The external devices will now sound and if fitted the strobe will flash. |
| 6. | Press [0/esc] | Display shows [bE] |
| 7. | Press [0/esc] | Display shows [_ _] |
| [walked] | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [no] | Display shows [tE]. |
| 4. | Press [yes/part] | Display shows[=]To walt test zone, speaker and keypad will both sound when zone is passed trough. |
| 5. | Press [yes/part] | to escape walk test. |
| 6. | Press [0/esc] | Display shows [tE] |
| 7. | Press [0/esc] | Display shows [_ _] |
| Setup user codes | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [no] | Display shows [tE]. |
| 4. | Press [no] | Display shows [bE]. |
| 5. | Press [no] | Display shows [Lo]. |
| 6. | Press [no] | Display shows [Ch]. |
| 7. | Press [no] | Display shows [Co]. |
| 8. | Press [yes/part] | Display shows [U-]. |
| 9. | Press [2] | Display shows [t-], enter the code type from 1-7 |
| 10. | Press [yes/part] | Display shows [--]. |
| 11. | Enter new [User code]. | |
| 12. | Press [yes/part] | Display shows [rE]. |
| 13. | Enter new [User code] | Again to confirm the selection. |
| 14. | Press [yes/part] | if re-entered correctly a short tone is generated. Display shows [U-]. |
| 15. | Press [0/esc] | Display shows [Co]. |
| 16. | Press [0/esc] | Display shows [_ _]. |
| View the event log | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [no] | Display shows [tE]. |
| 4. | Press [no] | Display shows [bE]. |
| 5. | Press [no] | Display shows [Lo]. |
| 6. | Press [yes/part] | |
| 7. | Press [yes/part] | To scroll forward to show more recent events |
| 8. | Press [0/esc] | Display shows [Lo]. |
| 9. | Press [0/esc] | Display shows [_ _] |
| Set control panel time/clock | ||
| 1. | Enter [user code] | Display shows [ ?]. |
| 2. | Press [no] | Within 20 seconds, display shows [O ]. |
| 3. | Press [no] | Display shows [tE]. |
| 4. | Press [no] | Display shows [bE]. |
| 5. | Press [no] | Display shows [Lo]. |
| 6. | Press [no] | Display shows [Ch]. |
| 7. | Press [no] | Display shows [Co]. |
| 8. | Press [no] | Display shows [CL]. |
| 9. | Press [yes/part] | Display shows [d-], Enter date and month. |
| 10. | Press [yes/part] | to confirm. Display shows [t-]. Enter the time in 24 hour mode. |
| 11. | Press [yes/part] | to confirm. Display shows [ ?] |
| 12. | Press [0/esc] | Display shows [_ _] |
| Back to Index | ||